Instruction/ maintenance manual of the product PRe3TM Bel Canto
Go to page of 10
PRe3 ™ T wo Channel Analog Pre-Amplifier Bel Canto Design, L TD. 212 Third A venue North Minneapolis, MN 55401 Phone: (612) 317.4550 Fax: (612) 359.9358 www .
page 3 © 2006 bel canto design, Ltd. PRe3 User’ s Guide 0206 Rev . A Please take a moment to fill out your warranty regis- tration sheet. Returning this registration validates your warranty . This information will not be sold or released outside Bel Canto.
The power supply on the PRe3 is preset for the proper national voltage. The power cable should have the correct plug for your local power system. If you believe this to not be true, please con- tact your dealer immediately .
page 5 © 2006 bel canto design, Ltd. PRe3 User’ s Guide 0206 Rev . A Because the PRe3 runs cool it can be placed in many system locations without compromise. W e do not recommend placing weights or other objects directly on the PRe3. This may mar or scratch the chassis finish.
page 6 © 2006 bel canto design, Ltd. PRe3 User’ s Guide 0206 Rev . A Front Panel Contr ol Knob: The control knob is a continuously rotat- ing control with a push-switch function. Standby Mode: Pressing and holding the control knob for 2 seconds will take the PRe3 out of Standby and in to operating mode.
page 7 © 2006 bel canto design, Ltd. PRe3 User’ s Guide 0206 Rev . A Mute: (available only on the remote) The PRe3 starts up in Soft Mute. This level is 20dB below the displayed vol- ume level. When MUTE is first pressed it goes to the Soft state, indicated by 2 decimal points on the volume display (i.
page 8 © 2006 bel canto design, Ltd. PRe3 User’ s Guide 0206 Rev . A V olume Up: Increases the output level in 0.5 Decibel (dB) steps over a range of 0.
page 9 © 2006 bel canto design, Ltd. PRe3 User’ s Guide 0206 Rev . A PRe3 Back Panel PRe3 Front Panel.
© 2006 bel canto design, Ltd. PRe3 User’ s Guide 0206 Rev . A page 10 Bandwidth • DC-200KHz V olume setting for unity gain • 80.0 Signal to Noise Ratio @ 2 V olt RMS • >105 dB A weighted, 20Hz-20kHz Distortion @ 2 V olt RMS/1kHz • <0.
Bel Canto Design, L TD. 212 Third A venue North Minneapolis, MN 55401 Phone: (612) 317.4550 Fax: (612) 359.9358 www .belcantodesign.com Info@belcantodesign.
An important point after buying a device Bel Canto PRe3TM (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bel Canto PRe3TM yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bel Canto PRe3TM - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bel Canto PRe3TM you will learn all the available features of the product, as well as information on its operation. The information that you get Bel Canto PRe3TM will certainly help you make a decision on the purchase.
If you already are a holder of Bel Canto PRe3TM, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bel Canto PRe3TM.
However, one of the most important roles played by the user manual is to help in solving problems with Bel Canto PRe3TM. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bel Canto PRe3TM along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
