Instruction/ maintenance manual of the product BCE 4012IM BTC
Go to page of 22
BCE 4012IM CD-ReWritable Drive User’s Manual.
CLASS 1 LA SER PRODUCT APPA REIL A LA SER DE CLASSE 1 LASER KLA SSE 1 LUOKAN 1 LA SERLAITE PRODUIT LASER CATEGORIE 1 DANGER INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM VORSICHT INSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN ATTENTION RADIATION DU FAISCEAU LASER INVISIBLE EN CAS D’OUVERTURE.
FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation.
Table of Contents INTRODUCTION 1 S YSTEM R EQUIREMENTS 1 P ACKAGE C ONTENTS 2 INSTALLATION 3 H OST I NTERFACE C ONNECTIONS 3 H ARDWARE I NSTALLATION 4 D RIVER I NSTALLATION 6 Windows Environment 6 DOS.
BCE 4012IM CD-ReWritable Drive 1 INTRODUCTION BCE 4012IM is a half-height CD-ReWritable drive of standard IDE interface. It supports maximum 40x speed writing ability on CD-R discs, 12x speed on CD-RW discs and 48x speed reading performance.
BCE 4012IM CD-ReWritable Drive ♦ Fast and sufficient hard disk space (minimum 150MB for installation, 1GB or more is recommended.) ♦ IDE host interface supporting ATAPI MMC command ♦ Operating s.
BCE 4012IM CD-ReWritable Drive INSTALLATION Host Interface Connections Most current mainboard models have two IDE ports (primary and secondary) which can connect two IDE cables. Two IDE cables allow you to connect up to four dev ices, but it is recommended that you separate IDE ports for your hard drive and your CD-ReWritable drive.
BCE 4012IM CD-ReWritable Drive 4 You may consider one of the two ways recommended below to connect your drive. ♦ To get the most stable performance for the CD-RW drive to write: Primary IDE Master: .
BCE 4012IM CD-ReWritable Drive The red-edge of the IDE Cable must be connected to Pin 1 on the CD- ReWritable drive. 5. If you have a sound card that can be connected to this CD- ReWritable drive, you can connect the drive (as Audio-out) and the sound card (as Audio-in) with a 4- pin audio cable.
BCE 4012IM CD-ReWritable Drive 6 Driver Installation Windows Environment BCE 4012IM is a PnP device, and Windows 95/98/ME and Windows NT/2000/XP can automatically detect the drive and load the appropriate driver. If Windows cannot detect the drive, you can operate manually: 1.
BCE 4012IM CD-ReWritable Drive CONNECTION & OPERATION Front Panel BUSY 1. Headphone Plug By plugging in the headphone jack here, you can listen to an audio CD (CD-DA disc) directly playing from the CD-ReWritable drive. 2. Headphone Volume Control This knob adjusts the audio output level.
BCE 4012IM CD-ReWritable Drive this hole for manual ejection. Please make sure to power off the system before you do that. 6. Play/Skip button Press this butt on to play tracks or skip to next track during the playing state. 7. Close/Eject button This button opens and closes the disc tray.
BCE 4012IM CD-ReWritable Drive 9 3. Device Configuration Jumper Set the jumper to Master, Slave or Cable Select according to your system configuration. 4. IDE Interface Connector Plug one end of the 40-pin IDE cable here to join the 40-pin IDE connector on the motherboard.
BCE 4012IM CD-ReWritable Drive 10 TECHNICAL DATA Performance Transfer rate Read: 7200kb/s (up to 48X) Write: CD-R 6000kb/s (up to 40X) CD-RW 1800kb/s (up to 12X) Access time ( ⅓ stroke) 100ms (full .
BCE 4012IM CD-ReWritable Drive 11 Power 5 VDC & 12VDC Dimensions Height 41.8 ± 0.2 mm Width 148.6 ± 0.3 mm Depth 193.3 ± 0.5 mm Weight 1 kg Disc Specification Capacity 120mm disc: 63min 553Mbyt.
BCE 4012IM CD-ReWritable Drive 12 Humidity Operating humidity 8% ~ 80%RH Non-operating humidity 5% ~ 95%RH.
BCE 4012IM CD-ReWritable Drive 13 TROUBLESHOOTING To help you get more familiar with BCE 4012IM, the following FAQ lists some common problems you might encounter. Please read it for reference before you request RMA support from your dealer. Q1. BCE 4012IM cannot be recognized.
BCE 4012IM CD-ReWritable Drive 14 Q5. BCE 4012IM doesn’t have power. Please check if the power cord is connected securely. Q6. The tray cannot be ejected. There are two possible reasons: (1) Need to be ejected by the application. Some of the burning or playing applic ation will lock the drive.
BCE 4012IM CD-ReWritable Drive 15 (3) Select good quality and high-speed supported blank discs. (4) Increase main memory capacity. (5) Select other burning software. (6) De-fragment the hard disk. (7) Keep the source & destination discs clean. (no scratches, fingerprints or contamination.
.
.
3974400010 Version 1.0 March 2002.
An important point after buying a device BTC BCE 4012IM (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought BTC BCE 4012IM yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data BTC BCE 4012IM - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, BTC BCE 4012IM you will learn all the available features of the product, as well as information on its operation. The information that you get BTC BCE 4012IM will certainly help you make a decision on the purchase.
If you already are a holder of BTC BCE 4012IM, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime BTC BCE 4012IM.
However, one of the most important roles played by the user manual is to help in solving problems with BTC BCE 4012IM. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device BTC BCE 4012IM along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center