Instruction/ maintenance manual of the product EG-40 Enviro
Go to page of 17
SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY THIS MANUAL IS PRINTED ON RECYCLED PAPER By SHERWOOD INDUSTRIES EG-40 Fireplace Insert Vented Room Heater OWNERS MANUAL Installation And Operating Instructions For Model:- EG-40 FPI.
SAFETY PRECAUTIONS FOR SAFE INSTALLATION AND OPERATION OF YOUR "ENVIROGAS" ROOM HEATER, PLEASE, CAREFULLY READ THE FOLLOWING INFORMATION: • All "ENVIROGAS" gas-fired appliances must be installed in accordance with these instructions.
TABLE OF CONTENTS 1 Code Appr ovals ..................................................................................................... 3 2 Specific ations .............................................................................................
3. ASSEMBL Y AND INST ALLA TION INSTRUCTIONS PREPARATION FOR INSTALLATION • Remove the packaging from the appliance, surround panels and log set, check to make sure there is no damage. Carefully check the glass door. Do not use the unit if it is damaged.
4.DECIDING WHERE TO LOCATE YOUR STOVE DIMENSIONS: A. Mantle pillar to stove 10"/ 25 cm B. Stove to 8" wide mantle 12"/ 31 cm Stove must sit on a non-combustible surface, the width and depth of the insert Maintain sufficient clearances for operation, service and maintenance OTHER DIMENSIONS A.
VENT TERMINAL CLEARANCES A= Clearance above grade, verandah, porch, deck, or [balcony (*12 inches (30 cm) minimum] B= Clearance to window or door that may be opened [*12 inches (30 cm) minimum] C= Cle.
5. VENTING WARNING; THIS APPLIANCE HAS BEEN DESIGNED TO OPERATE BY DRAWING COMBUSTION AIR AND DILUTION AIR FROM THE ROOM. IT IS ALSO DESIGNED TO DRAW ROOM AIR FOR PROPER HEAT CIRCULATION FROM THE SIDES OF THE UNIT. BLOCKING OR MODIFYING THE LOUVERS IN ANY WAY CAN CREATE HAZARDOUS SITUATIONS, EITHER THROUG H POOR VENTING OR BY OVERHEATING.
6. INSTALLATION OF LOG SET and EMBERS INSTALLING THE GLOWING EMBERS A bag of ceramic fiber embers is provided for use on the front burner ember tray. CAUTION: Use only the type of ember material supplied with this appliance. Due to the irregular size of the ember material there may be more than required.
7.OPERATING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE OPERATING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIO NS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE , PERSONAL INJURY OR LOSS OF LIFE. A) This appliance is equipped with a pilot, which must be lit by hand by following thes e instructions exactly.
8. ROUTINE MAINTENANCE Periodically check to ensure that the "B-Vent" venting system is clear and that a negative draft is present when the unit is operating. Periodically check the pilot and burner flames CLEANING OF GLASS Do not clean glass w hen hot It will be necessary to clean the ceramic glass periodically.
9. TROUBLE SHOOTING Problem Cause Solution Spark will not light the pilot after repeated pressing of spark ignitor Defective ignitor Check connections to ignitor -If ignitor connections are good but t.
10. GAS LINE CONNECTION ORIFICE SIZES, PRESSURE AND BTU’S NATURAL GAS PROPANE GAS FRONT BURNER #48 (1.93 mm) #55 (1.32 mm) REAR BURNER #41 (2.49 mm) #54 (1.40 mm) Manifold pressure. 3.8” w c (.95 kpa) 11” w c(2.74 kpa) Min. Manifold pressures. 1.
11. ELECTRICAL REQUIREMENTS The ENVIROGAS EG-40 FPI. BV. will operate without an external electrical pow er supply. This model has a Millivolt gas control which uses the pilot flame to generate enough electricity to operate the main burners.
12. PARTS AND ACCESSORIES Service Parts available from y our local Envirogas Dealer Burner Control Assembly Natural Gas Pilot Assembly Propane Pilot Assembly Door Bolt Relief Door Gasket Regulating Valve Piezo Igniter Burner Switch B-vent Spill switch 300 ° F(149 ° C) MR.
• There is a separate air shutter for each burner. • Remove one screw from the cove r plate located below the ash shelf. Loosen the other screw (do not remove) sw ing the cover plate out of the way and tighten screw dow n to hold it in place. • With along screwdriver rotate spring clips to open or close the shutter to the desired setting.
16 13. WARRANTY Sherwood Industries Ltd. offers a *Lifetime Warranty on this gas product. The lifetime warranty covers the appliance for a period of seven years from the date of in stallation.
14. INSTALLATION DATA SHEET The installer for warranty purposes and future reference must record the following information. Model: EG 40 FPI Name of Owner: __________________________________________ A.
An important point after buying a device Enviro EG-40 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Enviro EG-40 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Enviro EG-40 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Enviro EG-40 you will learn all the available features of the product, as well as information on its operation. The information that you get Enviro EG-40 will certainly help you make a decision on the purchase.
If you already are a holder of Enviro EG-40, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Enviro EG-40.
However, one of the most important roles played by the user manual is to help in solving problems with Enviro EG-40. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Enviro EG-40 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
