EN
NETGEAR logo
Official user manual

NETGEAR Wi-Fi Range Extender (WN3100RP)

20 pages·1.9 MB·Modem·PDF·ENDEFRITNLJA
NETGEAR Wi-Fi Range Extender (WN3100RP)
Table of Contents 17 sections Installation · N300 WiFi Range Extender Model WN3100RP · Getting Started · Meet Your Extender · … ShowHide
Page 1 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — Installation
Page 1 · click to enlarge
Page 1

Installation

N300 WiFi Range Extender Model WN3100RP

NETGEAR Wi-Fi Range Extender (WN3100RP) — Installation diagram (page 1)
Fig. 1 · Installation
Page 2 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — Getting Started
Page 2 · click to enlarge
Page 2

Getting Started

The NETGEAR WiFi Range Extender increases the distance of a WiFi network by boosting the existing WiFi signal and enhancing the overall signal quality over long distances. An extender repeats the signals from an existing WiFi router or access point.

NETGEAR Wi-Fi Range Extender (WN3100RP) — Getting Started diagram (page 2)
Fig. 2 · Getting Started
Page 3 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — WPS LED
Page 3 · click to enlarge
Page 3

Meet Your Extender

Before you install your extender, familiarize yourself with its LEDs, buttons, and port.

Front and Right Side Panels

WPS LED

Pass-through power socket (varies by region)

Show 6 more labels / short text on this page
Router Arrow LED · Client Arrow LED · Client Link LED · Router Link LED · Power LED · Ethernet port
Page 4 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — Rear and Left Side Panels
Page 4 · click to enlarge
Page 4

Rear and Left Side Panels

NETGEAR Wi-Fi Range Extender (WN3100RP) — Rear and Left Side Panels diagram (page 4)
Fig. 3 · Rear and Left Side Panels

Power connector (varies by region)

Show 4 more labels / short text on this page
Product label · WPS button · Factory Reset button · Device On/Off switch
Page 5 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — LED Descriptions
Page 5 · click to enlarge
Page 5

LED Descriptions

This LED indicates the connection between the extender and the router or access point. Solid green. Best connection. Solid amber. Good connection. Solid red. Poor connection. Off. No connection.

Client Link LED This LED indicates the connection between the extender and a computer or WiFi device. Solid green. Best connection. Solid amber. Good connection. Solid red. Poor connection. Off. No connection.

Power LED Solid amber. The extender is booting. Solid green. The extender is powered on. Off. The extender is powered off.

WPS LED Solid green. WiFi security is enabled (WPA or WPA2). Blinking green. A WPS connection is in progress. Off. WiFi security is not enabled.

blinks, see Find the Best Location on page 13. If no arrow LEDs light, the extender is in a good location.

or Client Arrow LED

Router Link LED

Page 6 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — Connect to an Existing WiFi Network
Page 6 · click to enlarge
Page 6

Install the WiFi Extender

Place the extender, apply power, and connect it to your WiFi network.

Place the Extender and Apply Power

1. Place your extender in the same room as your WiFi router. Proximity to the WiFi router is required only during the initial setup process.
2. Plug the extender into an electrical outlet. The Power LED lights green. If the Power LED does not light, slide the Device On/Off switch on the side of the extender to the On position.

Connect to an Existing WiFi Network

To extend the range of your WiFi network, you must connect the extender to your existing WiFi network. You can do this in one of two ways:

  • Connect with WPS . For more information, see Connect with WPS on page 7 .
  • Connect with web browser setup . For more information, see Connect with Web Browser Setup on page 9 .
Page 7 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — Connect with WPS
Page 7 · click to enlarge
Page 7

Connect with WPS

Wi-Fi Protected Setup (WPS) lets you join a secure WiFi network without typing the network name and password.

1. Press the WPS button on the side panel of the extender. The WPS LED blinks.
2. Within two minutes, press the WPS button on your router or access point. The WPS LED on the extender lights solid green, the Router Link LED

lights, and the extender connects to your existing WiFi network.

If the Router Link LED does not light, try again. If it still does not light, see Connect with Web Browser Setup on page 9.

3. Find the new extender network name on your computer or WiFi device. The extender’s wireless network name (SSID) changes to your existing WiFi network name, with _EXT at the end of the name, for example:
  • Existing WiFi network name . MyNetworkName
  • New extended network name . MyNetworkName_EXT
Page 8 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — Connect with WPS
Page 8 · click to enlarge
Page 8
4. Connect your computer or WiFi devices to the new extended WiFi network. Use the same WiFi password that you use for your WiFi router.
5. Unplug the extender and move it to a new location closer to the area with a poor WiFi signal. The location that you choose must be within the range of your existing WiFi router network.
6. Plug the extender into an electrical outlet. The Power LED lights green. If the Power LED does not light, slide the Device On/Off switch on the side of the extender to the On position.
7. Use the Router Link LED on the front panel to help you choose a spot where the extender-to-router connection is optimal.
Page 9 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — Connect with Web Browser Setup
Page 9 · click to enlarge
Page 9

Connect with Web Browser Setup

1. Use a WiFi network manager on a computer or WiFi device to find and connect to the NETGEAR_EXT (SSID) WiFi network. After the connection with the computer or WiFi device is established, the Client Link LED lights.
2. Open a web browser window from the same computer or WiFi device. The browser takes you directly to the NETGEAR genie web browser setup. If you are not automatically directed to NETGEAR genie, launch a web browser and enter www.mywifiext.net in the address field. Enter admin for the user name and password for the password.

The extender searches for WiFi networks in your area and displays a list.

NETGEAR Wi-Fi Range Extender (WN3100RP) — Connect with Web Browser Setup diagram (page 9)
Fig. 4 · Connect with Web Browser Setup
Page 10 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — Connect with Web Browser Setup
Page 10 · click to enlarge
Page 10
3. Select a WiFi network to extend and click the Continue button. The following screen displays:
NETGEAR Wi-Fi Range Extender (WN3100RP) — Connect with Web Browser Setup diagram (page 10)
Fig. 5 · Connect with Web Browser Setup
4. Type the network password (also called passphrase or security key) in the Password field and click the Continue button. The following screen displays:
NETGEAR Wi-Fi Range Extender (WN3100RP) — Connect with Web Browser Setup diagram (page 10)
Fig. 6 · Connect with Web Browser Setup
Page 11 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — Connect with Web Browser Setup
Page 11 · click to enlarge
Page 11
5. In the Name field, type the name (SSID) for your new extender WiFi network and click the Continue button. You can use the same security settings as the settings for your existing network by selecting the check box.

The settings are applied and the following screen displays.

NETGEAR Wi-Fi Range Extender (WN3100RP) — Connect with Web Browser Setup diagram (page 11)
Fig. 7 · Connect with Web Browser Setup

On iPads, iPhones, and MacBook computers, this screen automatically closes.

6. Use a WiFi network manager on the computer or WiFi device to connect to the extender’s newly created WiFi network. Repeat this step for all of your computers and WiFi devices.
Page 12 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — Connect with Web Browser Setup
Page 12 · click to enlarge
Page 12
7. If the screen is still displayed on your computer or WiFi device, select the check box at the bottom of the screen and click the Continue button.
NETGEAR Wi-Fi Range Extender (WN3100RP) — Connect with Web Browser Setup diagram (page 12)
Fig. 8 · Connect with Web Browser Setup

A message displays confirming that the extender is connected to the WiFi network.

8. Click the Finish button. 9. Unplug the extender and move it to a new location closer to the area with a poor WiFi signal. The location that you choose must be within the range of your existing WiFi router network.
10. Plug the extender into an electrical outlet. The Power LED lights green. If the Power LED does not light, slide the Device On/Off switch on the side of the extender to the On position.

Use the Router Link LED to help you choose a spot where the extender-to-router connection is optimal.

Page 13 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — Find the Best Location
Page 13 · click to enlarge
Page 13

Find the Best Location

If the WiFi signal is weak, the first time you join the extender network, an arrow LED blinks for two minutes. If this happens, adjust the position of the extender.

  • If the Router Arrow LED

blinks, move the extender closer to the router.

  • If the Client Arrow LED

blinks, move the computer or WiFi device closer to the extender.

If no arrow LEDs are lit, the extender is in a good location.

Page 14 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — Connect an Ethernet-Enabled Device
Page 14 · click to enlarge
Page 14

Connect an Ethernet-Enabled Device

After the extender is connected to your existing WiFi network, you can connect a wired device to the extender using an Ethernet cable. That device can then access your existing network through the WiFi connection.

NETGEAR Wi-Fi Range Extender (WN3100RP) — Connect an Ethernet-Enabled Device diagram (page 14)
Fig. 9 · Connect an Ethernet-Enabled Device
1. Set up the extender. For more information, see Place the Extender and Apply Power on page 6 .
2. Connect the extender to an existing WiFi network. For more information, see Connect to an Existing WiFi Network on page 6 .
3. Plug the Ethernet cable from an Ethernet-enabled device in to the Ethernet port on the extender.

WiFi router · Extender · Blu-ray player

Page 15 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — Log In to Access Extender Settings
Page 15 · click to enlarge
Page 15

Log In to Access Extender Settings

After installation, you can log in to the extender to view or change the extender’s settings.

1. Use a WiFi network manager on a computer or WiFi device to find and connect to the new extended WiFi network. After the connection with the computer or WiFi device is established, the Client Link LED lights.
2. Launch a web browser. 3. Enter www.mywifiext.net in the address field of the browser. A login screen displays.
4. Enter admin for the user name and password for the password. NETGEAR genie displays.
5. Make any needed changes.
Page 16 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — Frequently Asked Questions
Page 16 · click to enlarge
Page 16

Frequently Asked Questions

You can find more information about your product in the user manual, which is available at http://support.netgear.com.

The web browser setup guide keeps asking me for my network password (passphrase) or security key, and I am sure that I entered the correct password. What can I do?

The extender is probably placed at the borderline of the range covered by the router or access point. For more information, see Place the Extender and Apply Power on page 6.

If you are using WEP security, make sure that you are typing the network password in the correct field.

My router security is WEP, and I entered the wrong passphrase or security key on the extender. I cannot access the extender anymore. What can I do?

The extender cannot check to see if the WEP passphrase is correct. If you entered the wrong passphrase, your wireless device is not able to get the IP address from the extender. You must reset the extender to its factory default settings to get the IP address back.

Page 17 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — Frequently Asked Questions
Page 17 · click to enlarge
Page 17

How do I restore the extender to its factory default settings?

1. Use a sharp object such as a pen or paper clip to press and hold the Factory Reset button on the side of the extender for at least five seconds until the Power LED blinks amber. 2. Release the Factory Reset button and wait for the extender to reboot. The extender resets and returns to the factory default settings.

You can now access the extender from your web browser using the factory default settings.

Will the extender work if I connect it to the router with an Ethernet cable?

No. The extender is designed to connect wirelessly to the router or access point.

What are the user name and password to log in to the extender?

The user name is admin, and the default password is password. Both are case-sensitive.

Page 18 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — Frequently Asked Questions
Page 18 · click to enlarge
Page 18

I enabled a wireless MAC filter, wireless access control, or access control list (ACL) on my router. What should I do when installing the extender?

When the WiFi device connects through the extender to your router, the MAC address of the WiFi device shown on the router is translated to another MAC address. If your router’s MAC filter, wireless access control, or ACL is enabled, the WiFi device connects to the extender but cannot get an IP address from the extender and cannot access the Internet.

To allow the WiFi device to receive an IP address from the extender and access the Internet, you must provide the translated MAC address to the router.

1. Log in to your router and disable the MAC filter, wireless access control, or ACL. For more information about how to disable your router’s MAC filter, wireless access control, or ACL, see your router’s documentation.
2. Power on the extender and connect all of your WiFi devices to the extender network. 3. Make sure that the Router Link LED remains lit. 4. Log in to your extender: a. Launch a web browser. b. Enter www.mywifiext.net in the address field of the browser.
Page 19 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — Frequently Asked Questions
Page 19 · click to enlarge
Page 19

A login screen displays.

c. Enter admin for the user name and password for the password. 5. Select Maintenance > Attached Devices. The Attached Devices screen displays the MAC addresses and virtual MAC addresses for computers and WiFi devices that are connected to the extender network.

6. On the router, add all of the virtual MAC addresses from your extender to your router’s MAC filter table. 7. Enable the router’s MAC filter, wireless access control, or ACL.

I am connected to NETGEAR_EXT and launched a browser. Why can’t I see the web browser setup guide?

Try these troubleshooting steps:

  • Make sure that your computer is set up to use DHCP (most are).
  • Make sure that the Client Link LED is green and that you are using a valid IP address.
  • Relaunch the web browser and type <a href="http://www.mywifiext.net" rel="nofollow noopener" target="_blank">www.mywifiext.net</a> in the address field. Enter admin for the user name and password for the password.
Page 20 of the NETGEAR Wi-Fi Range Extender (WN3100RP) user manual — Frequently Asked Questions
Page 20 · click to enlarge
Page 20

Thank you for purchasing this NETGEAR product. After installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR recommends registering your product through the NETGEAR website.

For product updates and web support, visit http://support.netgear.com

NETGEAR recommends that you use only the official NETGEAR support resources. You can get the user manual online at http://downloadcenter.netgear.com or through a link in the product’s user interface.

NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice. © NETGEAR, Inc. All rights reserved.

For the current EU Declaration of Conformity, visit http://support.netgear.com/app/answers/detail/a_id/11621/.

For regulatory compliance information, visit http://www.netgear.com/about/regulatory/.

See the regulatory compliance document before connecting the power supply.

NETGEAR, Inc. 350 East Plumeria Drive San Jose, CA 95134, USA

Show 4 more labels / short text on this page
Support · Trademarks · Compliance · September 2014
Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the NETGEAR Wi-Fi Range Extender (WN3100RP)

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the NETGEAR Wi-Fi Range Extender (WN3100RP)

Be the first to ask — other owners or our team will answer.

Original document

NETGEAR Wi-Fi Range Extender (WN3100RP) manual PDF

20 pages·1.9 MB·Modem·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…