



350 East Plumeria Drive San Jose, CA 95134 USA
August 2012 202-11145-01 v1.0

© 2011 NETGEAR, Inc. All rights reserved
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means without the written permission of NETGEAR, Inc.
Thank you for choosing NETGEAR. To register your product, get the latest product updates, get support online, or for more information about the topics covered in this manual, visit the Support website at
http://support.netgear.com/app/answers/detail/a_id/984
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice. Other brand and product names are registered trademarks or trademarks of their respective holders. © 2011 NETGEAR, Inc. All rights reserved.
To improve internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use, or application of, the product(s) or circuit layout(s) described herein.
Technical Support · Trademarks · Statement of Conditions


The N300 Wireless ADSL2+ Modem Router DGN2200v3 provides you with an easy and secure way to set up a wireless home network with fast access to the Internet over a high-speed digital subscriber line (DSL). It has a built-in DSL modem, is compatible with all major DSL Internet service providers, lets you block unsafe Internet content and applications, and protects the devices (PCs, gaming consoles, and so on) that you connect to your home network.
For more information on the topics covered in this manual, visit the Support website at http://support.netgear.com.
If you want instructions about how to wall-mount your router, see Wall-Mount Your Router at http://support.netgear.com/app/answers/detail/a_id/18725.
If you have not already set up your new modem router using the installation guide that comes in the box, this chapter walks you through the hardware setup. Chapter 2, Modem Router Setup, explains how to set up your Internet connection.
This chapter contains the following sections:

Your box should contain the following items:
If any parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the carton and original packing materials, in case you need to return the product for repair.
Before you cable your modem router, take a moment to become familiar with the label and the front and back panels. Pay particular attention to the LEDs on the front panel.
The label on the bottom of the modem router shows the Restore Factory Settings button, security PIN, preset login information, MAC address, and serial number.

Wi-Fi network name MAC address Serial WPS Restore
and password Factory Settings
Figure 1. Sample label on the modem router bottom
See Preset Security on page 30 for information about preset security and MAC addresses. See Factory Settings on page 109 for information about restoring factory settings.
number security PIN · Hardware Setup

The back panel has the On/Off button and port connections as shown in the figure.

USB
Figure 2. Back panel port connections
The modem router front panel has the status LEDs and icons shown in the figure. Note that the Wireless and WPS icons are buttons.

Power LAN Ports (1-4) USB DSL Wireless WPS Internet
Figure 3. Front panel LEDs and icons
The following table describes the LEDs, icons, and buttons on the front panel from left to right.

Table 1. Front Panel LEDs
Hardware Setup

Table 1. Front Panel LEDs (continued)
For optimal wireless network performance, use the stand (included in the package) to position your modem router upright.

Hardware Setup

The modem router lets you access your network from virtually anywhere within the operating range of your wireless network. However, the operating distance or range of your wireless connection can vary significantly depending on the physical placement of your modem router. For example, the thickness and number of walls the wireless signal passes through can limit the range. For best results, place your modem router:
When you use multiple access points, it is better if adjacent access points use different radio frequency channels to reduce interference. The recommended channel spacing between adjacent access points is 5 channels (for example, use Channels 1 and 6, or 6 and 11).
If this is the first time you have cabled a router between a DSL phone line and your computer or laptop, you might not be familiar with ADSL microfilters. If you are, you can skip this section and proceed to Cable Your Modem Router on page 14.
An ADSL microfilter is a small in-line device that filters DSL interference out of standard phone equipment that shares the same line with your DSL service. Every telephone device that connects to a telephone line that provides DSL service needs an ADSL microfilter to filter out the DSL interference. Example devices are telephones, fax machines, answering machines, and caller ID displays. Note that not every phone line in your home necessarily carries DSL service. That depends on the DSL service setup in your home.
you purchased the modem router in a country where a microfilter is not included, you have to acquire the ADSL microfilter separately.
Hardware Setup

Plug the ADSL microfilter into the wall outlet and plug your phone equipment into the jack labeled Phone. The modem router plugs directly into a separate DSL line. Plugging the modem router into the phone jack blocks the Internet connection. If you do not have a separate DSL line for the modem router, the best thing to do is to use an ADSL microfilter with a built-in splitter (see Two-Line ADSL Microfilter )
Plugs into DSL line
Figure 4. One-line ADSL microfilter
If you do not have a separate DSL line for the modem router, the second-best solution is to get a separate splitter. To use a one-line filter with a separate splitter, insert the splitter into the phone outlet, connect the one-line filter to the splitter, and connect the phone to the filter.
Use an ADSL microfilter with a built-in splitter when there is a single wall outlet that provides connectivity for both the modem router and your telephone equipment. Plug the ADSL microfilter into the wall outlet, plug your phone equipment into the jack labeled Phone, and plug the modem router into the jack labeled ADSL.
Plugs into the DSL line
Figure 5. Two-line ADSL microfilter with built-in splitter
Hardware Setup


Figure 6. Cable connections
Incorrectly connecting a filter to your modem router blocks your DSL connection.
This section includes the same information on the printed installation guide that came with the modem router.
To cable the modem router:
a.
Install an ADSL microfilter between the phone line and the phone.

b. Connect the ADSL port of the modem router to the ADSL port of the microfilter
c. Use an ADSL microfilter for every phone line in the house if your modem router and
telephone connect to the same phone line.
Hardware Setup


a. Connect the power adapter to the router and plug the power adapter into an outlet.
b. Wait for the WiFi LED on the front panel to turn on. If none of the LEDs on the front
panel are on, press the Power On/Off button on the rear panel of the modem router.
You can use an Ethernet cable or connect wirelessly.

Hardware Setup

If a web page does not open, close and reopen the browser and enter http://routerlogin.net in the address bar.
in “pure bridge” or Modem mode, you need to log in to the modem and change the Device Mode setting to Modem mode. See Change the Device Mode on page 99.
Verify that your modem router is cabled correctly by checking the modem router LEDs. Turn on the modem router by pressing the On/Off button on the back.
The Power LED is green when the modem routeris turned on.
The LAN ports are green for each PC cabled to the modem router by an Ethernet cable.
The wireless LED is green when the modem router is turned on.
The DSL LED is green when you have a DSL connection.
The Internet LED is red when there is no Internet connection.
Turn on your computer. If software usually logs you in to your Internet connection, do not run that software. Cancel it if it starts automatically.
Verify that the LAN
LEDs (1 through 4) are lit for any computers cabled to the modem router by an Ethernet cable.

This chapter explains how to set up your Internet connection using one of three methods: NETGEAR Genie®, Setup Wizard, or manual setup. If you have already set up your modem router using one of these methods, the initial setup is complete. Refer to this chapter if you want to become familiar with the modem router menus, view or adjust the initial settings, or change the modem router password and login time-out.
This chapter contains the following sections:

You can set up your modem router with the NETGEAR Genie as described in NETGEAR Genie Setup on page 19, with the Setup Wizard as described in Setup Wizard on page 22, or manually as described in Manual Setup (Basic Settings) on page 23. However, before you start the setup process, you need to have your ISP information and to make sure the laptops, PCs, and other devices in the network have the settings described here.
If you set up your computer to use a static IP address, you have to change the settings back so that it uses Dynamic Host Configuration Protocol (DHCP).
To replace an existing modem and router, disconnect them and set them aside before starting the modem router setup.
You need the following information to set up your modem router and to check that your Internet configuration is correct. Your Internet service provider (ISP) should have provided you with all the information needed to connect to the Internet. If you cannot locate this information, ask your ISP to provide it. When your modem router Internet connection is set up, you no longer need to launch the ISP’s login program on your computer to access the Internet. When you start an Internet application, your modem router automatically logs you in.
- ISP login name and password
- ISP Domain Name Server (DNS) addresses
- Fixed or static IP address
- Host and domain names
- Depending on how your ISP set up your Internet account, you could need to know one or more of these settings for a manual setup:
- Virtual path identifier (VPI) and virtual channel identifier (VCI) parameters
- Host and domain names
- Multiplexing method · Modem Router Setup

NETGEAR Genie is the easiest way to set up the modem router because it automates many steps and verifies that those steps have been successfully completed. It takes about 15 minutes to complete.
Your browser automatically displays the NETGEAR Genie screen.
Your modem router connects to the Internet when any computer on your network launches a Web browser to access the Internet. The modem router’s Internet LED
blinks.
You can view and change the settings in the following ways:
that was placed on your desktop during the NETGEAR Genie setup, or use an Internet browser. See Log In to the Modem Router on page 20.
When the NETGEAR Genie is done, your modem router has the following settings. Some of these can be viewed in Router_Setup.html.
Modem Router Setup

You can log in to the modem router to view or change settings or to set up the modem router.
To log in:


from the user name and password for logging in to your Internet connection. See Types of Logins on page 28 for more information.
The modem router screen displays as described in Modem Router Interface on page 21.
If you do not see the login prompt:
Modem Router Setup

When you log in, if you are connected to the Internet, the Firmware Upgrade Assistant screen displays so you can upgrade to the latest firmware. See Chapter 5, Network Maintenance, for more information about upgrading firmware.
To upgrade the firmware:
Do not try to go online, turn off the modem router, shut down the computer, or do anything else to the modem router until the modem router finishes restarting and the Ready light has stopped blinking for several seconds.
You cannot upgrade firmware until you have established your Internet connection as described in Setup Wizard on page 22.
The modem router interface lets you view or change the modem router settings. The left column has menus, and the right column provides online help. The middle column is the screen for the current menu option.

Help for the current
(scroll down to view more)
Figure 7. Modem Router interface

device mode setting to Modem Mode, then menu items not supported in Modem Mode will be grayed out.
If you do not use the NETGEAR Genie, you have to log in to the modem router to set the country, language, and Internet connection. If you performed the NETGEAR Genie setup, the country, language, Internet, and wireless network settings are already configured.
To use the Setup Wizard:

Modem Router Setup

With automatic Internet detection, the Setup Wizard searches your Internet connection for servers and protocols to determine your ISP configuration.
(PPTP) connection. If your ISP uses PPTP, you have to set your Internet connection through the screen described in Manual Setup (Basic Settings) on page 23.
The Basic Settings screen displays when you select No. I want to configure the Router myself in the Setup Wizard and is also available from the modem router menu. It is where you view or change ISP information. The fields that display vary depending on whether or not your Internet connection requires a login.
To use Basic Settings to specify your Internet settings manually:
before proceeding with the manual setup.
1. Select Set Up > Basic Settings, and select Yes or No depending on whether or not your ISP requires a login. Figure , The following descriptions explain all of the possible fields in the Basic Settings screen. Note that which fields appear in this screen depends on whether or not an ISP login is required. shows both forms of the Basic Settings screen. • Yes. Select the encapsulation method and enter the login name. If you want to change the login time-out, enter a new value in minutes.
Modem Router Setup

ISP does not require login ISP does require login


The following descriptions explain all of the possible fields in the Basic Settings screen. Note that which fields appear in this screen depends on whether or not an ISP login is required.
Does Your ISP Require a Login? Answer either yes or no.
Account Name (If required). Enter the account name provided by your ISP. This might also be called the host name.
Domain Name (If required). Enter the domain name provided by your ISP.
Encapsulation. Encapsulation is a method for enclosing multiple protocols. PPP stands for Point-to-Point Protocol. The choices are PPPoE (PPP over Ethernet) or PPPoA (PPP over ATM).
Login. The login name provided by your ISP. This is often an email address.
Password. The password that you use to log in to your ISP.
Connection Mode. Specify whether your Internet connection is always on, or is off by default unless you are using it.
Modem Router Setup

Idle Timeout (In minutes). If you want to change the login timeout, enter a new value in minutes. This determines how long the modem router keeps the Internet connection active after there is no Internet activity from the LAN. Entering a value of 0 (zero) means never log out.
connection reset setting. This can be used to set the specific time that the modem router automatically disconnects from the Internet.
Internet IP Address.
Get Dynamically from ISP. Your ISP uses DHCP to assign your IP address. Your ISP automatically assigns these addresses.
Use Static IP Address. Enter the IP address, IP subnet mask, and the gateway IP address that your ISP assigned. The gateway is the ISP’s modem router to which your modem router will connect.
Use IP Over ATM (IPoA). Your ISP uses classical IP addresses (RFC 1577). Enter the IP address, IP subnet mask, and gateway IP addresses that your ISP assigned.
Domain Name Server (DNS) Address. The DNS server is used to look up site addresses based on their names.
NAT (Network Address Translation). NAT automatically assigns private IP addresses (10.1.1.x) to LAN-connected devices.
Modem Router Setup

When no login is required, this field displays:
Router MAC Address. The Ethernet MAC address used by the modem router on the Internet port. Some ISPs register the MAC address of the network interface card in your computer when your account is first opened. They will then accept traffic only from the MAC address of that computer. This feature allows your modem router to use your computer’s MAC address (this is also called cloning).
DSL settings of your modem router work fine for most ISPs. However, some ISPs use a multiplexing method and virtual circuit number for the virtual path identifier (VPI) and virtual channel identifier (VCI).
the default DSL settings to work.
To manually specify the ADSL settings:
If your ISP provided you with a multiplexing method or VPI/VCI number, enter the setting:

Modem Router Setup

For security reasons, the modem router has its own user name and password that default to admin and password. You can and should change these to a secure user name and password that are easy to remember. The ideal password contains no dictionary words from any language and is a mixture of upper case and lower case letters, numbers, and symbols. It can be up to 30 characters.
the user name and password for logging in to your Internet connection. See Types of Logins on page 28 for more information about login types.
To change the password and login time-out:

Modem Router Setup

The administrator’s login to the modem router configuration times out after a period of inactivity to prevent someone else from accessing the modem router interface when you step away.
After changing the password, you are required to log in again to continue the configuration. If you have backed up the modem router settings previously, you should do a new backup so that the saved settings file includes the new password. See To back up the modem router configuration file: on page 59 for information about backing up your network configuration.
The modem router interface provides a Logout command at the bottom of the modem router menus. Log out when you expect to be away from your computer for a relatively long period of time.
There are three separate types of logins that have different purposes. It is important that you understand the difference so that you know which login to use when.
Modem Router Setup

This chapter describes how to use the Wireless Settings screens to view and change (if needed) your wireless network settings. Security features to prevent objectionable content from reaching your PCs are covered in Chapter 4, Security Settings.
This chapter contains the following sections:
A wireless adapter is the wireless radio in your PC or laptop that lets the PC or laptop connect to a wireless network. Most PCs and laptops come with an adapter already installed, but if it is outdated or slow, you can purchase a USB adapter to plug into a USB port.
Make sure the wireless adapter in each computer in your wireless network supports the same security settings as the modem router. See Preset Security on page 30 for information about the modem router’s preconfigured security settings.
described in Wi-Fi Protected Setup (WPS) Method on page 32, those devices assume the security settings of the modem router.

The modem router comes with preset security. This means that the Wi-Fi network name (SSID), passphrase, and security option (encryption protocol) are preset in the factory. You can find the preset SSID and passphrase on the bottom of the unit.
device to protect and maximize your wireless security.
The Wireless Settings screen lets you view and change the preset security settings. However, NETGEAR recommends that you not change your preset security settings. If you do decide to change your preset security settings, make a note of the new settings and store it in a safe place where you can easily find it.
Unlike wired network data, wireless data transmissions extend beyond your walls and can be received by any device with a compatible wireless adapter (radio). For this reason, it is very important to maintain the preset security and understand the other security features available to you. Besides the preset security settings described in the previous section, your modem router has the security features described here and in Chapter 4, Security Settings.
You can turn off the wireless connectivity of the modem router by pressing the Wireless On/Off button on its front panel
. For example, if you use your laptop to wirelessly connect to your modem router and you take a business trip, you can turn off the wireless portion of the modem router while you are traveling. Other members of your household who use computers connected to the modem router through Ethernet cables can still use the modem router.
Wireless Settings

By default, the modem router broadcasts its Wi-Fi network name (SSID) so devices can find it. If you change this setting to not allow the broadcast, wireless devices will not find your modem router unless they are configured with the same SSID.
feature of some products such as Windows XP, but the data is still fully exposed to a determined snoop using specialized test equipment like wireless sniffers. If you allow the broadcast, be sure to keep wireless security enabled.
You can enhance your network security by allowing access to only specific PCs based on their Media Access Control (MAC) addresses. You can restrict access to only trusted PCs so that unknown PCs cannot wirelessly connect to the modem router. The Wireless Station MAC address filtering adds additional security protection to the wireless security option that you have in force. The Access list determines which wireless hardware devices are allowed to connect to the modem router by MAC address. See Advanced Wireless Settings on page 85 for the procedure.
A security option is the type of security protocol applied to your wireless network. The security protocol encrypts data transmissions and ensures that only trusted devices receive authorization to connect to your network. There are several types of encryption: Wi-Fi Protected Access II (WPA2), WPA, and Wired Equivalent Privacy (WEP). WPA2 is the latest and most secure, and is recommended if your equipment supports it. WPA has several options including pre-shared key (PSK) encryption and 802.1x encryption for enterprises. Note that it is also possible to disable wireless security. NETGEAR does not recommend this. You can view or change the wireless security options in the Wireless Settings screen. See Wireless Settings Screen on page 33.
Choose either the manual or the WPS method to add wireless computers or devices to your wireless network.
Wireless Settings

To join the wireless network:
Wi-Fi Protected Setup (WPS) is a standard that lets you easily join a secure wireless network with WPA or WPA2 wireless security. The modem router automatically sets security for each computer or device that uses WPS to join the wireless network. To use WPS, make sure that your wireless devices are Wi-Fi certified and support WPS. NETGEAR products that use WPS call it Push 'N' Connect.1
WPS client, the Keep Existing Wireless Settings check box on the Advanced Wireless Settings screen has been cleared. See WPS Settings on page 86 for more information about this setting.
You can use a WPS button or the modem router interface method to add wireless computers and devices to your wireless network.
To join the wireless network using a WPS button:
WPS button on the modem router front panel.
To use the modem router Interface to add a client:
Wireless Settings


WPS Push button method
The PIN method displays this screen so you can enter the client security PIN number:

While the modem router attempts to connect, the WPS LED on the front of the modem router blinks green. When the modem router establishes a WPS connection, the LED is solid green and the modem router WPS screen displays a confirmation message.
The Wireless Settings screen lets you view or change the wireless network settings. Note that your preset modem router has a unique network name and password, located on the product label. NETGEAR recommends that you use these settings. If you decide to change them, note the new settings and save them in a secure location.
name (SSID) or security options, you are disconnected when you click Apply. To avoid this problem, use a computer with a wired connection to access the modem router.
WPS PIN method · Wireless Settings

Before you begin, check the following:
Your preset modem router comes set up with a unique wireless network name (SSID) and network password. This information is printed on the label for your modem router. You view or change these settings in the Wireless Settings screen. You can also use this screen to set up guest wireless networks.
To view or change wireless settings:

Wireless Settings

following sections.
a. Use your wireless computer or device to join your network. When prompted, enter the network password.
b. From the wirelessly connected computer, make sure that you can access the
Internet.
The primary network is the one that you usually use. You can set up guest networks too. You can customize access so that people who use their computers to access your guest network can use the Internet, but they do not have access to the rest of your home network.
The Security Options section of the Wireless Settings screen lets you change the security option and passphrase. The primary network for your preset modem router is already set up with WPA2 and WPA security. NETGEAR recommends that you set up wireless security for each guest network that you plan to use. For information about changing these settings, see the following sections.
Wireless Network · Security Options Settings · Wireless Settings

To change the WPA Security Option and passphrase:

To set up WEP security:

Wireless Settings

- For 64-bit WEP, enter 10 hexadecimal digits (any combination of 0–9, a–f, or
A–F).
- For 128-bit WEP, enter 26 hexadecimal digits (any combination of 0–9, a–f, or
A–F).
Make sure that you understand how the WEP key settings are configured in your wireless adapter. Wireless adapter configuration utilities such as the one in Windows XP allow one key entry, which has to match the default key you set in the modem router.
A wireless guest network allows you to provide guests access to your wireless network without prior authorization of each individual guest. You can set up wireless guest networks and specify the security options for each wireless guest network.
Select Setup > Guest Network to display the following screen:

Enable Guest Network. Select this check box if you want to use a guest network.
Enable SSID Broadcast. This setting allows the modem router to broadcast its SSID so wireless stations can see this wireless name (SSID) in their scanned network lists. This check box is selected by default. To turn off the SSID broadcast, clear the Allow Broadcast of Name (SSID) check box and click Apply.
Wireless Settings

Allow guests to access My Local Network. If you want guests to have access to your home network instead of just Internet access, then select this check box.
Enable Wireless Isolation. If this check box is selected, then wireless clients (computers or wireless devices) that join the network can use the Internet, but cannot access each other or access Ethernet devices on the network.
Guest Wireless Network Name (SSID). Change the network name to one that you will easily recognize.
Security Options. NETGEAR strongly recommends that you set up wireless security for your guest network. For information about wireless security, see Security Basics on page 30
To set up a wireless guest network:
Wireless Settings

This chapter explains how to use the basic firewall features of the modem router to prevent objectionable content from reaching the PCs and other devices connected to your network.
This chapter contains the following sections:

The modem router logs security-related events such as denied incoming service requests, hacker probes, and administrator logins. If you enable content filtering in the Block Sites screen, the Logs screen show you when someone on your network tries to access a blocked site. If you enable email notification, you will receive these logs in an email message.
To view the log, select Security > Logs. A screen similar to the following displays:

The Include in Log check boxes allow you to select which events are logged. You can write the logs to a computer running a syslog program. To activate this feature, select Broadcast on LAN, or enter the IP address of the server where the syslog file will be written. The security log entries include the following information:
Security Settings

Following are examples of log messages. In all cases, the log entry shows the time stamp as day, year-month-date hour:minute:second.
Tue, 2006-05-21 18:48:39 - NETGEAR activated
[This entry indicates a power-up or reboot with initial time entry.]
Tue, 2006-05-21 18:55:00 - Administrator login successful-IP:192.168.0.2
Thu, 2006-05-21 18:56:58 - Administrator logout - IP:192.168.0.2
[This entry shows an administrator logging in and out from IP address 192.168.0.2.]
Tue, 2006-05-21 19:00:06 - Login screen timed out - IP:192.168.0.2
[This entry shows a time-out of the administrator login.]
Wed, 2006-05-22 22:00:19 - Log emailed
[This entry shows when the log was emailed.]
Wed, 2006-05-22 07:15:15 - TCP packet dropped - Source:64.12.47.28,4787,WAN - Destination:134.177.0.11,21,LAN - [Inbound Default rule match]
Sun, 2006-05-22 12:50:33 - UDP packet dropped - Source:64.12.47.28,10714,WAN - Destination:134.177.0.11,6970,LAN - [Inbound Default rule match] Sun, 2006-05-22 21:02:53 - ICMP packet dropped - Source:64.12.47.28,0,WAN - Destination:134.177.0.11,0,LAN - [Inbound Default rule match]
[These entries show an inbound FTP (port 21) packet, a User Datagram Protocol (UDP) packet (port 6970), and an Internet Control Message Protocol (ICMP) packet (port 0) being dropped as a result of the default inbound rule, which states that all inbound packets are denied.]
Activation and Administration · Dropped Packets · Security Settings

Use keyword blocking to prevent certain types of HTTP traffic from accessing your network. The blocking can be always or according to a scheduled.
To block sites using keywords:

The Keyword list. supports up to 32 entries. Here are some sample entries:
To delete a keyword or domain:
To specify a trusted computer:
You can exempt one trusted computer from blocking and logging. The computer you exempt has to have a fixed IP address.
Security Settings

Your modem router has a firewall that blocks unauthorized access to your wireless network and permits authorized inbound and outbound communications. Authorized communications are established according to inbound and outbound rules. The firewall has the following two default rules. You can create custom rules to further restrict the outbound communications or more widely open the inbound communications:
The Firewall Rules screen lets you configure custom rules to make exceptions to the default rules. Exceptions can be based on the service or application, source or destination IP addresses, and time of day. You can log traffic that matches or does not match the rule and change the order of rule precedence.
All traffic attempting to pass through the firewall is subjected to the rules in the order shown in the Rules table from the top (highest precedence) to the default rules at the bottom. In some cases, the order of precedence is important to determine which communications are allowed into or out of the network.
To set up firewall rules:

For To edit or delete a rule, select its button on the left side and click Edit or Delete.
a. Select the button on the left side of the rule and click Move.
b. At the prompt, enter the number of the new position and click OK.
Security Settings

Some application servers (such as FTP and IRC servers) send replies back to multiple port numbers. Using the port triggering function of your router, you can tell the router to open additional incoming ports when a particular outgoing port originates a session.
An example is Internet Relay Chat (IRC). Your computer connects to an IRC server at destination port 6667. The IRC server not only responds to your originating source port, but also sends an “identify” message to your computer on port 113. Using port triggering, you can tell the router, “When you initiate a session with destination port 6667, you have to also allow incoming traffic on port 113 to reach the originating computer.” Using steps similar to the preceding example, the following sequence shows the effects of the port triggering rule you have defined:
Security Settings

To configure port triggering, you need to know which inbound ports the application needs. Also, you need to know the number of the outbound port that will trigger the opening of the inbound ports. You can usually determine this information by contacting the publisher of the application or the relevant user groups or news groups.
In both of the preceding examples, your computer initiates an application session with a server computer on the Internet. However, you might need to allow a client computer on the Internet to initiate a connection to a server computer on your network. Normally, your router ignores any inbound traffic that is not a response to your own outbound traffic. You can configure exceptions to this default rule by using the port forwarding feature.
A typical application of port forwarding can be shown by reversing the client-server relationship from the previous web server example. In this case, a remote computer’s browser needs to access a web server running on a computer in your local network. Using port forwarding, you can tell the router, “When you receive incoming traffic on port 80 (the standard port number for a web server process), forward it to the local computer at 192.168.1.123.” The following sequence shows the effects of the port forwarding rule you have defined:
Destination address. The IP address of www.example.com which is the address of your router.
Destination port number. 80, which is the standard port number for a web server process.
The remote computer then sends this request message through the Internet to your router.
The destination address is replaced with 192.168.1.123.
Your router then sends this request message to your local network.
Security Settings

To configure port forwarding, you need to know which inbound ports the application needs. You usually can determine this information by contacting the publisher of the application or the relevant user groups or news groups.
The following points summarize the differences between port forwarding and port triggering:
Using the port forwarding feature, you can allow certain types of incoming traffic to reach servers on your local network. For example, you might want to make a local web server, FTP server, or game server visible and available to the Internet.
Use the Port Forwarding/Port Triggering screen to configure the router to forward specific incoming protocols to computers on your local network. In addition to servers for specific applications, you can also specify a default DMZ server to which all other incoming protocols are forwarded.
Before starting, you need to determine which type of service, application, or game you want to provide, and the local IP address of the computer that will provide the service. The server computer has to always have the same IP address.
use the reserved IP address feature of your product.
Security Settings

To forward specific incoming protocols:


To define a service, game, or application that does not appear in the Service Name list, you have to first determine which port number or range of numbers is used by the application. You can usually determine this information by contacting the publisher of the application or user groups or news groups. When you have the port number information, follow these steps.
To add a custom service:
Security Settings


To edit or delete a port forwarding entry:
If you host a web server on your local network, you can use port forwarding to allow web requests from anyone on the Internet to reach your web server.
To make a local web server public:
Security Settings

Port triggering is a dynamic extension of port forwarding that is useful in these cases:
When port triggering is enabled, the router monitors outbound traffic looking for a specified outbound “trigger” port. When the router detects outbound traffic on that port, it remembers the IP address of the local computer that sent the data. The router then temporarily opens the specified incoming port or ports, and forwards incoming traffic on the triggered ports to the triggering computer.
While port forwarding creates a static mapping of a port number or range to a single local computer, port triggering can dynamically open ports to any computer that needs them and can close the ports when they are no longer needed.
connections, real-time communications such as instant messaging, or remote assistance (a feature in Windows XP), you should also enable Universal Plug and Play (UPnP).
To configure port triggering, you need to know which inbound ports the application needs. Also, you need to know the number of the outbound port that will trigger the opening of the inbound ports. You can usually determine this information by contacting the publisher of the application or user groups or news groups.
To enable port triggering:
Security Settings


configure port triggering, port triggering is disabled. However, any port triggering configuration information you added to the router is retained even though it is not used.
To add a port triggering service:
Make sure that you enable port triggering so that the service that you add will be used.
Security Settings


Security Settings

The modem router uses the Network Time Protocol (NTP) to obtain the current time and date from one of several network time servers on the Internet.
To set the time zone:

Security Settings

If you enabled service blocking in the Block Services screen or port forwarding in the Ports screen, you can set up a schedule for when blocking occurs or when access is not restricted.
To schedule services:
Security Settings

To receive logs and alerts by email, provide your email information in the E-mail screen and specify which alerts you want to receive and how often.
Select Security > Email to display the following screen:

- Days specifies which day of the week to send the log. This is relevant when the log is sent weekly.
Security Settings

- Time specifies the time of day to send the log. This is relevant when the log is sent daily or weekly.
before the specified period, the log is automatically emailed to the specified email address. After the log is sent, it is cleared from the modem router’s memory. If the modem router cannot email the log file, the log buffer might fill up. In this case, the modem router overwrites the log and discards its contents.
Security Settings

This chapter describes the modem router settings for administering and maintaining the modem router and home network.
This chapter contains the following sections:

The modem router firmware (routing software) is stored in flash memory. By default, when you log in to your modem router, it checks the NETGEAR website for new firmware and alerts you if there is a newer version.
When automatic firmware checking is on, the modem router performs the check and notifies you if an upgrade is available or not as shown here.


To upgrade the firmware:
When uploading firmware to the modem router, do not interrupt the Web browser by closing the window, clicking a link, or loading a new page. If the browser is interrupted, it could corrupt the firmware.
problem has been detected with the modem router’s firmware. Follow the prompts to correct the problem or see Incorrect Date or Time on page 107 for a description of the steps.
Network Maintenance

To stop automatic firmware checking:
You can turn the automatic firmware checking off and check for firmware updates manually if you prefer. See Manually Check for Firmware Upgrades on page 58.
To turn off the automatic firmware check at login:

You can use the Router Upgrade screen to manually check the NETGEAR website for newer versions of firmware for your product.
To manually check for firmware, and upgrade the modem router:
When uploading firmware to the modem router, do not interrupt the Web browser by closing the window, clicking a link, or loading a new page. If the browser is interrupted, it could corrupt the firmware.
Network Maintenance


When the upload is complete, your modem router restarts. The upgrade process typically takes about 1 minute. Read the new firmware release notes to determine whether or not you need to reconfigure the modem router after upgrading.
The modem router configuration settings are stored in a configuration file (*.cfg). This file can be backed up to your computer, restored, or used to revert to factory default settings.
To back up the modem router configuration file:

Network Maintenance

To restore the configuration file:
Upon completion, the modem router reboots.
To erase the configuration:
Click the Erase button to reset the modem router to its factory default settings. Erase sets the password to password, the LAN IP address to 192.168.0.1, and enables the modem router’s DHCP.
Select Maintenance > Router Status to display this screen. The Router Status screen provides status and usage information.

Hardware and Firmware Version. The model of the hardware and the currently running firmware version.
Network Maintenance

GUI Language Version. The currently selected language.
MAC Address. The Ethernet MAC address of the DSL port.
IP Address. The DSL port IP address. If no address is shown, the modem router cannot connect to the Internet.
Network Type. The value depends on your ISP.
IP Subnet Mask. The DSL port IP subnet mask.
Gateway IP Address. The IP address used as a gateway to the Internet for computers configured to use DHCP.
Domain Name Server. The modem router DNS server IP addresses. These addresses are usually obtained dynamically from the ISP.
MAC Address. The modem router LAN port Ethernet MAC address.
IP Address. The modem router LAN port IP address. The default is 192.168.0.1.
DHCP. If Off, the modem router does not assign IP addresses to PCs on the LAN. If On, the modem router does assign IP addresses to PCs on the LAN.
IP Subnet Mask. The IP subnet mask used by the modem router LAN. The default is 255.255.255.0.
ADSL Firmware Version. The version of the firmware.
Modem Status. The connection status of the modem.
DownStream Connection Speed. The modem receives data from the DSL line at this speed.
UpStream Connection Speed. The modem transmits data to the DSL line at this speed.
VPI. The Virtual Path Identifier setting.
VCI. The Virtual Channel Identifier setting.
See Wireless Settings Screen on page 33 for a more detailed description of these settings.
Name (SSID). The Wi-Fi network name (service set ID) for the wireless network.
Region. The country where the unit is set up for use.
Network Maintenance

Channel. The current channel, which determines the operating frequency.
Mode. The current mbps setting.
Wireless AP. Indicates if the access point feature is enabled. If disabled, the Wireless LED on the front panel is off.
Broadcast Name. Indicates if the modem router is configured to broadcast its SSID.
Click the Show Statistics button on the Router Status screen to display a screen similar to this:

The statistics for the WAN (Internet), LAN (local), and wireless LAN (WLAN) ports. For each port, the screen displays the following:
ADSL Link Downstream or Upstream
The statistics for the upstream and downstream DSL link. These statistics are of interest to your technical support representative if you have problems obtaining or maintaining a connection.
Port · Network Maintenance

In the Router Status screen, click the Connection Status button to display a screen similar to this:

The Attached Devices screen shows all IP devices that the modem router has discovered on the local network.
Network Maintenance

Select Maintenance > Attached Devices.

For each device, the table shows the IP address, the device name if available, and the Ethernet MAC address. Note that if the modem router is rebooted, the table data is lost until the modem router rediscovers the devices. To force the modem router to look for attached devices, click the Refresh button.
The modem router has a diagnostics feature. Select Maintenance > Diagnostics to display the following screen.

You can perform the following functions:
Network Maintenance

This chapter describes how to access and configure a USB storage drive attached to your modem router.

Figure 8. USB port on rear panel.
The USB port on the modem router can be used only to connect USB storage devices like flash drives or hard drives. Do not connect computers, USB modems, printers, CD drives, or DVD drives to the this USB port.
This chapter includes the following sections:

The modem router works with 1.0 and 1.1 (USB Full Speed) and 2.0 (USB High Speed) standards. The approximate USB bus speeds are shown in the following table. Actual bus speeds can vary, depending on the CPU speed, memory, speed of the network, and other variables.
Table 2. USB Drive Speeds
USB 1.1 12 Mbits
USB 2.0 480 Mbits
The modem router should work with most USB-compliant external flash and hard drives. For the most up-to-date list of USB drives supported by the modem router, go to:
http://kbserver.netgear.com/readyshare
The modem router supports both read and write for FAT16, FAT32, NTFS, and Linux file systems (EXT2 and EXT3).
be loaded in to the PC before the PC can access the USB device. Such USB devices do not work with the modem router.
Once you have set up your modem router, you can connect any USB storage device and share the contents with other users on your network.
You can access your USB device in any of the following ways:
Bus Speed/Sec · USB Storage

You can share files on the USB drive for a wide variety of business and recreational purposes. The files can be any PC, Mac, or Linux file type including text files, Word, PowerPoint, Excel, MP3, pictures, and multimedia. USB drive applications include:
A few common uses are described in the following sections.
You can create your own central storage location for photos and multimedia. This eliminates the need to log in to (and pay for) an external photo-sharing site.
To share files with your friends and family:
Computers on your local area network (LAN) can automatically access this USB drive using a web browser or Microsoft Networking.
Storing Files in a Central Location for Printing
This scenario is for a family that has one high-quality color printer directly attached to a computer, but not shared on the local area network (LAN). This family does not have a print server.
To print photos from a Mac on the printer attached to a PC:
Sharing Photos · USB Storage

Sharing Large Files over the Internet
Sending files that are larger than 5 MB can pose a problem for many email systems. The modem router allows you to share very large files such as PowerPoint presentations or .zip files over the Internet. FTP can be used to easily download shared files from the modem router.
Sharing files with a remote colleague involves the following considerations:
USB Storage screen to share large files. This option supports downloading files only.
You can view or edit basic settings for the USB storage device attached to your modem router. Select USB > Basic Settings. The following screen displays:

If you logged in to the modem router before you connected your USB device, you might not see your USB device in the modem router screens until you log out and then log in again. This screen includes the following fields and buttons:
USB Storage

If Not Shared is shown, then the default share has been deleted and no other share for the root folder exists. Click the link to change this setting.
- All no password allows all users to access the network folder.
- admin uses the same password that you use to log in to the modem router main menu.
To access a USB device attached to the modem router USB port:
By default, the USB device is available to all computers on your local area network (LAN).
USB Storage

Network/device name:

Share name:

If you logged in to the modem router before you connected your USB device, you might not see your USB device in the modem router screens until you log out and then log in again.
You can use the Edit button on either the USB Storage (Basic Settings) or USB Storage (Advanced Settings) screen.
To edit a network folder:

\\readyshare · \\readyshare\USB_Storage · USB Storage

To view or change advanced USB settings, select USB > Advanced Settings. The USB Storage (Advanced Settings) screen displays:
You can use this screen to specify access to the USB storage device. The settings are as follows:
Access Method · USB Storage

You can create a network folder on the USB device that is attached to the USB port on the rear panel of the modem router.
To create a network folder:

Available Network Folders · USB Storage

To unmount a USB disk drive so that no users can access it, from the USB Settings screen, click the Safely Remove USB button. This takes the drive offline.
Unmount the USB drive before physically unplugging it from the modem router. If the USB disk is removed or a cable is pulled while data is being written to the disk, it could result in file or disk corruption.
You can set up the modem router to work with compatible media adapters. Select USB Storage > Media Servers to display the following screen:

Enable Media Server. If this feature is enabled, the DGN2200v3 can be located by compatible media adapters, using the UPnP AV standard developed by Intel and its partners. Media content on the DGN2200v3 (in the Content Directories that you specify) can then be accessed and played by the media adapters.
Server Name. The name of the media server that is displayed on client devices. Note that some special characters (such as " / \ [ ] : ; |= , + * ? < > ` ( ) # $ %) and 2-byte characters cannot be used in the server name.
Content Directory. Specify the directories (folders) that the media server should scan for media content. You can specify up to four. Click the Browse button to locate and select the folder you want. Each directory can be limited to a certain media type. The default setting will scan for all content types. Note that some special characters (e.g. " \ : * ? < > | ' `) cannot be used in the folder names.
USB Storage

You can specify which USB devices are approved for use when connected to the modem router.
To allow only approved USB devices to be accessed:


If you want to approve another USB device, you must first use the Safely Remove USB Device button to unmount the currently connected USB device. Connect the other USB device, and then repeat this process.
USB Storage

To connect to the USB drive from remote computers using a Web browser, you use the modem router’s Internet port IP address.
To connect to the modem router’s USB drive using a Web browser:
a. Select Maintenance > Router Status.
b. Record the IP address that is listed for the Internet port. This is the IP address you
can use to connect to the modem router remotely.
For example, type ftp://10.1.65.4. If you are using Dynamic DNS, you can type the DNS name rather than the IP address.
The directories of the USB drive that your account has access to display, for example, share/partition1/directory1. You can now read and copy files from the USB directory.
You can access the USB drive from local computers on your home or office network using Microsoft network settings. You must be running Microsoft Windows 2000, XP, or older versions of Windows with Microsoft networking enabled. You can use normal Explorer operations such as dragging and dropping, opening files, or cutting and pasting files from:
Each computer’s network properties have to be set to enable network communication with the USB drive. File and Printer Sharing for Microsoft networking have to be enabled, as described in the following sections.
enabled by default.
USB Storage

Configuring Windows 98SE and Windows ME
The easiest way to get to your network properties is to go to your desktop, right-click Network Neighborhood and then select Properties. File and Printer Sharing for Microsoft Windows should be listed. If not, click Add and follow the installation prompts.
Microsoft for assistance.
Configuring Windows 2000 and Windows XP
Right-click the network connection for your local area network. File and Printer Sharing for Microsoft Windows should be listed. If not, click Install and follow the installation prompts.
USB Storage

This chapter describes the advanced features of your modem router. The information is for users with a solid understanding of networking concepts who want to set the modem router up for unique situations such as when remote access from the Internet by IP or domain name is needed.
This chapter contains the following sections:
For information about the Port Forwarding/Port Triggering menu selection, see Set Up Port Forwarding to Local Servers on page 46 and Set Up Port Triggering on page 49.
For information about Advanced USB Settings, see Approved USB Devices (Advanced USB Settings) on page 74.

Select Advanced > WAN Setup to display the following screen:

The following settings are available:
Advanced Settings

The default demilitarized zone (DMZ) server feature is helpful when you use online games and video conferencing applications that are incompatible with NAT. The modem router is programmed to recognize some of these applications and to work correctly with them, but there are other applications that might not function well. In some cases, one local computer can run the application correctly if that computer’s IP address is entered as the default DMZ server.
feature. When a computer is designated as the default DMZ server, it loses much of the protection of the firewall. If compromised via the Internet, the computer can be used to attack your network.
Incoming traffic from the Internet is usually discarded by the modem router unless the traffic is a response to one of your local computers or a service that you have configured in the Ports screen. Instead of discarding this traffic, you can have it forwarded to one computer on your network. This computer is called the default DMZ server.
To assign a computer or server to be a default DMZ server:

Advanced Settings

If your network has a permanently assigned IP address, you can register a domain name that is linked to your IP address by public Domain Name Servers (DNS). More commonly, Internet accounts have dynamically assigned IP addresses in which the IP addresses change frequently. In this case, use a commercial Dynamic DNS service to register your domain to its IP address and forward traffic directed at your domain to your current IP address.
The modem router has a client that can connect to a Dynamic DNS service provider. Once you set up Dynamic DNS in the modem router, when your IP address changes, your modem router contacts your Dynamic DNS service provider, logs in to your account, and registers your new IP address.
To set up Dynamic DNS:

If your ISP assigns a private WAN IP address such as 192.168.x.x or 10.x.x.x, the Dynamic DNS service does not work because private addresses are not routed on the Internet.
Advanced Settings

The LAN Setup screen allows configuration of LAN IP services such as DHCP and Routing Information Protocol (RIP). The modem router is shipped preconfigured to use private IP addresses on the LAN side and to act as a DHCP server. The modem router’s default LAN IP configuration is as follows:
These addresses are part of the private address range designated by the Internet Engineering Task Force (IETF http://www.ietf.org/) for use in private networks, and should be suitable in most applications. If your network has a requirement to use a different IP addressing scheme, you can make those changes in the LAN Setup screen.
connected through the browser, you are disconnected. To reconnect, open a new connection to the new IP address and log in.
To change the LAN settings:

Advanced Settings

- When set to Both or Out Only, the modem router broadcasts its routing table periodically.
- When set to Both or In Only, the modem router incorporates the RIP information that it receives.
For most applications, the default DHCP and TCP/IP settings of the modem router are satisfactory.
To reserve an IP address:
the Attached Devices screen and paste it here.
Advanced Settings

To edit or delete a reserved address entry:
Quality of Service (QoS) is an advanced feature that can be used to prioritize some types of traffic ahead of others. The modem router can provide QoS prioritization over the wireless link and on the Internet connection.
The modem router supports Wi-Fi Multimedia Quality of Service (WMM QoS) to prioritize wireless voice and video traffic over the wireless link. WMM QoS provides prioritization of wireless data packets from different applications based on four access categories: voice, video, best effort, and background. For an application to receive the benefits of WMM QoS, both it and the client running that application have to have WMM enabled. Legacy applications that do not support WMM, and applications that do not require QoS, are assigned to the best effort category, which receives a lower priority than voice and video.
To set up QoS:

Advanced Settings


Advanced Settings

To view or change advanced wireless settings:

WEP as the security option.
on the front panel of the router. If this button is pressed, then the Enable Wireless Router Radio check box is automatically updated.
Wireless button · Advanced Settings

Router’s PIN. The PIN number that you use on a registrar (for example, from the Network Explorer on a Vista Windows PC) to configure the modem router’s wireless settings through WPS. You can also find the PIN on the modem router label.
The PIN function might temporarily be disabled when the modem router detects suspicious attempts to break into the modem router’s wireless settings by using the modem router’s PIN through WPS. You can manually enable the PIN function by clearing the Disable Router’s PIN check box.
Keep Existing Wireless Settings. By default, the Keep Existing Wireless Settings check box is selected. This allows the modem router to keep the same SSID and wireless security settings when WPS-enabled devices are added to the network.
If the Keep Existing Wireless Settings check box is not selected, the next time you use WPS to connect WPS-capable devices to your wireless network, the modem router generates a new random SSID and WPA/WPA2 passphrase. NETGEAR does not recommend this.
The Wireless Card Access List lets you restrict access to your network to a specific list of devices based on their MAC addresses.
To set up a wireless card access list:

The Turn Access Control On check box is not selected so that any computer configured with the correct wireless network name (SSID) and passphrase to access the network.
Advanced Settings

the wireless modem router from a wired computer or from a wireless computer that is on the access control list. The following screen displays:

You can copy and paste the MAC addresses from the modem router’s Attached Devices screen (see View Attached Devices on page 63) into the MAC Address field. This screen shows computers connected to the network.
The Remote Management screen lets you allow a user or users on the Internet to configure, upgrade, and check the status of your modem router. Select Advanced > Remote Management to display this screen:

Advanced Settings

To set up remote management:
Web browser access usually uses the standard HTTP service port 80. For greater security, you can change it so the remote modem router interface uses a custom port by entering that number in the field provided. Choose a number between 1024 and 65535, but do not use the number of any common service port. The default is 8080, which is a common alternate for HTTP.
To access your modem router from the Internet, type your modem router’s WAN IP address in your browser’s Address field, followed by a colon (:) and the custom port number. For example, if your external address is 134.177.0.123 at port number 8080, enter the following in your browser: http://134.177.0.123:8080.
Static routes provide additional routing information to your modem router. Under normal circumstances, the modem router has adequate routing information after it has been configured for Internet access, and you do not need to configure additional static routes. You configure static routes only for unusual cases such as multiple routers or multiple IP subnets located on your network.
As an example of when a static route is needed, consider the following case:
Advanced Settings

When you first configured your modem router, two implicit static routes were created. A default route was created with your ISP as the modem router, and a second static route was created to your local network for all 192.168.0.x addresses. With this configuration, if you attempt to access a device on the 134.177.0.0 network, your modem router forwards your request to the ISP. The ISP forwards your request to the company where you are employed, and the request is likely to be denied by the company’s firewall.
In this case you need to define a static route, telling your modem router that 134.177.0.0 should be accessed through the ISDN router at 192.168.0.100

In this example:
To add a static route:

Advanced Settings


Universal Plug and Play (UPnP) helps devices, such as Internet appliances and computers, access the network and connect to other devices as needed. UPnP devices can automatically discover the services from other registered UPnP devices on the network.
Advanced Settings

To set up UPnP:

Advanced Settings

Traffic metering allows you to monitor the volume of Internet traffic passing through your modem router’s Internet port. With the Traffic Meter utility, you can set limits for traffic volume, set a monthly limit, and get a live update of traffic usage.
To monitor traffic on your modem router:

Advanced Settings

the Wireless Settings screen and change the wireless security setting of the router to WEP or None, and you have to change the Channel field to a different setting than Auto, which is the default. For more information, see Wireless Settings Screen on page 33.
With the modem router, you can build large bridged wireless networks that form an IEEE 802.11n Wireless Distribution System (WDS). Using the modem router with other access points (APs) and wireless devices, you can connect clients using their MAC addresses rather than IP addresses. Here are some examples of wireless bridged configurations:
The wireless bridging and repeating feature uses the default security profile to send and receive traffic.
Advanced Settings

Select Advanced > Wireless Repeating Function to display the following screen:

- If you are setting up a point-to-point bridge, select this check box.
- If you want all client traffic to go through the other access point (repeater with wireless client association), leave this check box cleared.
Advanced Settings

In point-to-point bridge mode, the modem router communicates as an access point with another bridge-mode wireless station. As a bridge, wireless client associations are disabled. Only wired clients can be connected. Use wireless security to protect this communication. The following figure shows an example of point-to-point bridge mode.

Both access points (APs) are in
point-to-point bridge mode.
AP 1 (DGN2200 modem router)
192.168.0.1
Figure 9. Point-to-point bridge example
To set up a point-to-point bridge configuration:
a. In the Wireless Repeating Function screen, select the Enable Wireless Repeating Function check box.
b. Select either the Wireless Repeater or Wireless Base Station radio button.
c. Select the corresponding Disable Wireless Client Association check box.
d. Enter the MAC address for the other access point in the bridge. Depending on your
selection in step a, use either the Base Station MAC Address field or the Repeater MAC Address 1 field.
e. Click Apply.
If your modem router is the repeater, then set up AP 2 as the base station; otherwise set up AP 2 as the repeater.

Multi-point bridge mode allows a router to bridge to multiple peer access points simultaneously. Wireless client associations are disabled. Only wired clients can be connected.

AP 1 DGN2200 modem router
192.168.0.1
PCs Hub or switch
Figure 10. Multi-point bridge example
Multi-point bridge mode configuration includes the following steps:
To set up the multi-point bridge configuration:
In this example, the modem router is AP 1 on LAN Segment 1 because it is in a central location.
a. In the Wireless Repeating Function screen for your modem router, select the Enable Wireless Repeating Function check box.
b. Select the Wireless Base Station radio button.
c. Select the corresponding Disable Wireless Client Association check box.
d. Enter the MAC address for the other access points in the bridge in the Repeater
MAC Address 1 and Repeater MAC Address 2 fields.

e. Click Apply.
a. In the Wireless Repeating Function screen for AP 2 and AP 3, select the Enable Wireless Repeating Function check box.
b. Select the Wireless Repeater radio button.
c. Select the corresponding Disable Wireless Client Association check box.
d. Enter the MAC addresses for your modem router in the Base Station MAC Address
field.
e. Click Apply.
connect to the modem router or access points. If you want wireless stations to access any LAN segment, use additional access points in any LAN segment.
In the repeater mode with wireless client association, your modem router sends all traffic to a base station access point. You can set up the modem router as either the base station (parent) or as the repeater (child) access point.
Advanced Settings

The following figure shows an example of a repeater mode configuration.

Wireless PC with AP 1 associated
AP 2 in repeater mode
192.168.0.1
AP 1 (parent AP in repeater mode)
AP 3 in repeater mode
Figure 11. Repeater example
To set up a repeater with wireless client association:
In this example, the modem router is the base station, but you can set it up to be the repeater with another AP as the base station if you want.
a. In the Wireless Repeating Function screen for your modem router, select the Enable Wireless Repeating Function check box.
b. Select the Wireless Base Station radio button.
c. Clear the corresponding Disable Wireless Client Association check box (make
sure it is not selected).
d. Enter the MAC addresses for AP 2 and AP 3 in the Repeater MAC Address 1 and
Repeater MAC Address 2 field.
e. Click Apply.
a. In the Wireless Repeating Function screen for AP 2 and AP 3, select the Enable Wireless Repeating Function check box.
b. Select the Wireless Repeater radio button.
c. Clear the corresponding Disable Wireless Client Association check box (make
sure it is not selected).
d. Enter the MAC addresses for your modem router in the Base Station MAC Address
field.
e. Click Apply.

Verify connectivity across the LANs. A computer on any LAN segment should be able to connect to the Internet or share files and printers with any other PCs or servers connected to any of the three WLAN segments.
The modem includes a built-in router. If you want to configure the modem as a “pure bridge” in Modem mode, first set up the Internet connection and then change the Device Mode setting to Modem mode. In Modem mode, the device acts as a “pure bridge” or DSL modem. When the device is in Modem mode, features that are not available are grayed out.
To change the device mode:

By default, the modem is in Router mode.
Advanced Settings

This chapter provides information to help you diagnose and solve problems you might have with your modem router. If you do not find the solution here, check the NETGEAR support site at http://support.netgear.com for product and contact information.
This chapter contains the following sections:

When you turn the power on, the power, LAN, and DSL LEDs should light as described here. If they do not, refer to the sections that follow for help.
a. The LAN port LEDs light for any local ports that are connected.
b. The DSL link LED lights to indicate that there is a link to the connected device.
c. If a LAN port is connected to a 100 Mbps device, verify that the LAN port’s LED is
green. Note that if the LAN port is 10 Mbps, the LED is amber.
Power LAN Ports (1–4) USB DSL Wireless WPS Internet
Figure 12. Front panel LEDs
If the Power and other LEDs are off when your modem router is turned on:
If the error persists, you could have a hardware problem and should contact NETGEAR Technical Support.
When the modem router is turned on, it performs a power-on self-test during which time the Power LED turns red. If the Power LED does not turn green within a minute or so or if it turns red at any other time during normal operation there is a fault within the modem router.
Troubleshooting

If the Power LED turns red to indicate a modem router fault, turn the power off and on to see if the modem router recovers. If the power LED is still red 1 minute after power-up:
If the error persists, you could have a hardware problem and should contact NETGEAR Technical Support.
If the appropriate LAN LED does not light when the Ethernet connection is made, check the following:
If you are unable to log in to the modem router from a computer on your local network, check the following:
Troubleshooting

If your modem router is unable to access the Internet, you should check the ADSL connection, then the WAN TCP/IP connection.
If your modem router is unable to access the Internet, you should first determine whether you have an ADSL link with the service provider. The state of this connection is indicated with the Internet LED.
ADSL Link LED Is Green
If your ADSL link LED is green, then you have a good ADSL connection. You can be confident that the service provider has connected your line correctly and that your wiring is correct.
ADSL Link LED Is Blinking Green
If your ADSL link LED is blinking green, then your modem router is attempting to make an ADSL connection with the service provider. The LED should turn green within several minutes.
If the ADSL link LED does not turn green, disconnect all telephones on the line. If this solves the problem, reconnect the telephones one at a time, being sure to use a microfilter on each telephone. If the microfilters are connected correctly, you should be able to connect all your telephones.
If disconnecting telephones does not result in a green ADSL link LED, there might be a problem with your wiring. If the telephone company has tested the ADSL signal at your network interface device (NID), then you might have poor-quality wiring in your house.
ADSL Link LED Is Off
If the ADSL link LED is off, disconnect all telephones on the line. If this solves the problem, reconnect the telephones one at a time, being sure to use a microfilter on each telephone. If the microfilters are connected correctly, you should be able to connect all your telephones.
If disconnecting telephones does not result in a green ADSL link LED, check for the following:
Troubleshooting

If the Internet LED is red, the device was unable to connect to the Internet. Verify the following:
If your modem router is unable to access the Internet, and your Internet LED is green, you should determine whether the modem router is able to obtain an Internet IP address from the ISP. Unless you have been assigned a static IP address, your modem router requests an IP address from the ISP. You can determine whether the request was successful using the browser interface.
To check the Internet IP address from the browser interface:
If your modem router is unable to obtain an IP address from the ISP, the problem might be one of the following:
- Inform your ISP that you have bought a new network device, and ask them to use the modem router’s MAC address.
- Configure your modem router to spoof your computer’s MAC address. This can be done in the Basic Settings screen.
The PPPoE or PPPoA connection can be debugged as follows:
Troubleshooting

If you cannot connect after several minutes, you might be using an incorrect service name, user name, or password. There also might be a provisioning problem with your ISP.
authenticate using PPPoE or PPPoA until data is transmitted to the network.
If your modem router can obtain an IP address, but your computer is unable to load any Web pages from the Internet:
A DNS server is a host on the Internet that translates Internet names (such as www addresses) to numeric IP addresses. Typically your ISP provides the addresses of one or two DNS servers for your use. If you entered a DNS address when you set up the modem router, reboot your computer, and verify the DNS address. Alternatively, you can configure your computer manually with DNS addresses, as explained in your operating system documentation.
If your computer obtains its information from the modem router by DHCP, reboot the computer, and verify the modem router address.
Most TCP/IP terminal devices and routers have a ping utility for sending an echo request packet to the designated device. The device responds with an echo reply to tell whether a TCP/IP network is responding to requests.
You can ping the modem router from your computer to verify that the LAN path to your modem router is set up correctly.
Troubleshooting

To ping the modem router from a PC running Windows 95 or later:
ping 192.168.0.1
You should see a message like this one:
Pinging with 32 bytes of data
If the path is working, you see this message:
Reply from < IP address >: bytes=32 time=NN ms TTL=xxx
If the path is not working, you see this message:
If the path is not functioning correctly, you could have one of the following problems:
- Make sure that the LAN port LED is on. If the LED is off, follow the instructions in
LAN LED Is Off on page 102.
- Check that the corresponding link LEDs are on for your network interface card and
for the hub ports (if any) that are connected to your workstation and modem router.
- Verify that the Ethernet card driver software and TCP/IP software are both
installed and configured on your PC or workstation.
- Verify that the IP address for your modem router and your workstation are correct
and that the addresses are on the same subnet.
After you verify that the LAN path works correctly, test the path from your PC to a remote device. In the Windows Run screen, type:
ping -n 10 IP address
where IP address is the IP address of a remote device such as your ISP’s DNS server.
If the path is functioning correctly, replies as described in Test the LAN Path to Your Modem Router on page 105 display. If you do not receive replies:
Request timed out · Troubleshooting

If the modem router does not save the changes you make in the modem router interface, check the following:
Select Security > Schedule to display the current date and time. The modem router uses the Network Time Protocol (NTP) to obtain the current time from one of several network time servers on the Internet. Each entry in the log is stamped with the date and time of day. Problems with the date and time function can include the following:
Troubleshooting

A. Supplemental Information
This appendix includes the factory default settings and technical specifications for the N300 Wireless ADSL2+ Modem Router DGN2200v3, and instructions for wall-mounting the unit.
This appendix contains the following sections:

You can return the modem router to its factory settings. On the bottom of the modem router, use the end of a paper clip or some other similar object to press and hold the Restore Factory Settings button
for at least 7 seconds. The modem router resets, and returns to the factory settings. Your device will return to the factory configuration settings shown in the following table.
Table 3. Factory Default Settings
Router Login User login URL www.routerlogin.com or /www.routerlogin.net
User name (case-sensitive) admin
Login password (case-sensitive) password
WAN MAC address Use default address
WAN MTU size 1492
Subnet mask 255.255.255.0
Local network (LAN) continued
DHCP starting IP address 192.168.0.2
DHCP ending IP address 192.168.0.254
DMZ Enabled or disabled
Time zone GMT for WW except NA and GR, GMT+1 for GR, GMT-8 for NA
Time zone adjusted for daylight savings time
Firewall Inbound (communications coming in from the Internet)
Disabled (except traffic on port 80, the HTTP port)
Outbound (communications going out to the Internet)
Source MAC filtering Disabled

Table 3. Factory Default Settings (continued)
Wireless Wireless communication Enabled
SSID name Can be found on the label on the bottom of the unit.
Security Can be found on the label on the bottom of the unit.
Country/region United States (in North America; otherwise, varies by region)
Operating mode Up to 145 Mbps
Authentication type Pre-Shared Key
Wireless card access list All wireless stations allowed

Network protocol and standards compatibility
TCP/IP, RIP-1, RIP-2, DHCP, PPPoE or PPPoA, RFC 1483 Bridged or Routed Ethernet, and RFC 1577 Classical IP over ATM
Physical Dimensions: 6.80 in. x 5.03 in. x 1.28 in. (173 mm x 128 mm x 33 mm)
Regulatory compliance FCC Part 15 Class B; VCCI Class B; EN 55 022 (CISPR 22), Class B
Network protocol and standards compatibility
TCP/IP, RIP-1, RIP-2, DHCP, PPPoE or PPPoA, RFC 1483 Bridged or Routed Ethernet, and RFC 1577 Classical IP over ATM
Interface specifications LAN: 10BASE-T or 100BASE-Tx, RJ-45 WAN: ADSL, Dual RJ-11, pins 2 and 3 T1.413, G.DMT, G.Lite ITU Annex A hardware or Annex B hardware ITU G.992.5 (ADSL2+)
Specification Description · Supplemental Information

B. Notification of Compliance
Europe – EU Declaration of Conformity
Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards:
EN300 328 (2.4Ghz), EN301 489-17 EN60950-1
For complete DoC, visit the NETGEAR EU Declarations of Conformity website at:
http://support.netgear.com/app/answers/detail/a_id/11621
EDOC in Languages of the European Community
Cesky [Czech] NETGEAR Inc. tímto prohlašuje, že tento Radiolan je ve shode se základními požadavky a dalšími príslušnými ustanoveními smernice 1999/5/ES.
Dansk [Danish] Undertegnede NETGEAR Inc. erklærer herved, at følgende udstyr Radiolan overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Hiermit erklärt NETGEAR Inc., dass sich das Gerät Radiolan in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Eesti [Estonian] Käesolevaga kinnitab NETGEAR Inc. seadme Radiolan vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
English Hereby, NETGEAR Inc., declares that this Radiolan is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Regulatory Compliance Information · Language Statement · Deutsch [German]

Por medio de la presente NETGEAR Inc. declara que el Radiolan cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ NETGEAR Inc. ∆ΗΛΩΝΕΙ ΟΤΙ Radiolan ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ.
Par la présente NETGEAR Inc. déclare que l'appareil Radiolan est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
Italiano [Italian] Con la presente NETGEAR Inc. dichiara che questo Radiolan è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Ar šo NETGEAR Inc. deklarē, ka Radiolan atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Šiuo NETGEAR Inc. deklaruoja, kad šis Radiolan atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Hierbij verklaart NETGEAR Inc. dat het toestel Radiolan in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Malti [Maltese] Hawnhekk, NETGEAR Inc., jiddikjara li dan Radiolan jikkonforma mal-htigijiet essenzjali u ma provvedimenti ohrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Alulírott, NETGEAR Inc. nyilatkozom, hogy a Radiolan megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Polski [Polish] Niniejszym NETGEAR Inc. oświadcza, że Radiolan jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
NETGEAR Inc. declara que este Radiolan está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.
NETGEAR Inc. izjavlja, da je ta Radiolan v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.
NETGEAR Inc. týmto vyhlasuje, že Radiolan spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
Suomi [Finnish] NETGEAR Inc. vakuuttaa täten että Radiolan tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Härmed intygar NETGEAR Inc. att denna Radiolan står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

Hér með lýsir NETGEAR Inc. yfir því að Radiolan er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.
NETGEAR Inc. erklærer herved at utstyret Radiolan er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services.
This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 - 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.
FCC Requirements for Operation in the United States
FCC Information to User
This product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals.
FCC Guidelines for Human Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Declaration of Conformity
We, NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that the N300 Wireless ADSL2+ Modem Router DGN2200v3 complies with Part 15 Subpart B of FCC CFR47 Rules. Operation is subject to the following two conditions:
FCC Radio Frequency Interference Warnings & Instructions
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following methods:

Canadian Department of Communications Radio Interference Regulations
This digital apparatus (N300 Wireless ADSL2+ Modem Router DGN2200v3) does not exceed the Class B limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.
This Class [B] digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
GPL may be included in this product; to view the GPL license agreement go to
ftp://downloads.netgear.com/files/GPLnotice.pdf.
For GNU General Public License (GPL) related information, please visit
http://support.netgear.com/app/answers/detail/a_id/2649
Industry Canada · GPL License Agreement · Notification of Compliance

The table below shows the Recommended Minimum Distance between NETGEAR equipment and household appliances to reduce interference (in feet and meters).
Household Appliance Recommended Minimum Distance (in feet and meters)
Microwave ovens 30 feet / 9 meters
Baby Monitor - Analog 20 feet / 6 meters
Baby Monitor - Digital 40 feet / 12 meters
Cordless phone - Analog 20 feet / 6 meters
Cordless phone - Digital 30 feet / 9 meters
Bluetooth devices 20 feet / 6 meters
ZigBee 20 feet / 6 meters
Interference Reduction Table · Notification of Compliance



Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.